Search results for "Polymer solar cell"
showing 10 items of 43 documents
Nonfullerene Polymer Solar Cells Reaching a 9.29% Efficiency Using a BODIPY-Thiophene Backboned Donor Material
2018
A conjugated polymer donor containing BODIPY-thiophene dyads in the backbone, P(BdP-EHT), combined with a low bandgap nonfullerene acceptor (SMDPP) consisting of carbazole and diketopyrrolopyrrole units linked with a tetracyanobutadiene acceptor π-linker, was used to design bulk heterojunction polymer solar cells. After the optimization of the donor to acceptor weight ratio and solvent vapor annealing of the P(BdP-EHT):SMDPP active layer, the resulting polymer solar cell showed an overall power conversion efficiency of 9.29%, which is significantly higher than that for the polymer solar cell based on PC71BM (7.41%) processed under identical conditions. This improved power conversion efficie…
Energy level determination in bulk heterojunction systems using photoemission yield spectroscopy: case of P3HT:PCBM
2018
Financial support provided by Scientific Research Project for Students and Young Researchers Nr. SJZ2015/20 realized at the Institute of Solid State Physics, University of Latvia, is greatly acknowledged. This work has been supported by the Latvian State Research Program on Multifunctional Materials IMIS2. Jennifer Mann from Physical Electronics is greatly acknowledged for providing UPS data.
Bi-Layer GaOHPc:PCBM/P3HT:PCBM Organic Solar Cell
2011
Simultaneous determination of carrier lifetime and electron density-of-states in P3HT:PCBM organic solar cells under illumination by impedance spectr…
2010
We report new insights into recombination kinetics in poly(3-hexylthiophene):methanofullerene (P3HT:PCBM) bulk heterojunction (BHJ) solar cells, based on simultaneous determination of the density of states (DOS), internal recombination resistance, and carrier lifetime, at different steady states, by impedance spectroscopy. A set of measurements at open circuit under illumination was performed aiming to better understand the limitations to the photovoltage, which in this class of solar cells remains far below the theoretical limit which is the difference between the LUMO level of PCBM and the HOMO of P3HT (∼1.1 eV). Recombination kinetics follows a bimolecular law, being the recombination ti…
Polymer solar cells with novel fullerene-based acceptor
2004
Abstract Alternative acceptor materials are possible candidates to improve the optical absorption and/or the open circuit voltage of polymer–fullerene solar cells. We studied a novel fullerene-type acceptor, DPM-12, for application in polymer–fullerene bulk heterojunction photovoltaic devices. Though DPM-12 has the identical redox potentials as methanofullerene PCBM, surprisingly high open circuit voltages in the range V OC =0.95 V were measured for OC 1 C 10 -PPV:DPM-12-based samples. The potential for photovoltaic application was studied by means of photovoltaic characterization of solar cells including current–voltage measurements and external quantum yield spectroscopy. Further studies …
New BODIPY derivatives with triarylamine and truxene substituents as donors for organic bulk heterojunction photovoltaic cells
2021
Abstract We have designed two new BODIPY derivatives, denoted as 6a and 6b, substituted with truxene moiety and triphenylamine (TPA) unit groups and have investigated their optical and electrochemical properties. Dyes 6a and 6b were employed as donor along with PC71BM or Y6 as acceptor for the fabrication of binary and ternary organic solar cells. After optimization of the binary and ternary active layers, we have achieved over all power conversion efficiency (PCE) of 11.37 % and 13.32% for 6a:PC71BM:Y6 and 6b:PC71BM:Y6 ternary organic solar cells, respectively, which are higher than the binary organic solar cells based on PC71BM or Y6 acceptor. The higher power conversion efficiency for te…
Electrodes for GaOHPc:PCBM/P3HT:PCBM bulk heterojunction solar cell
2012
Abstract The bulk heterojunction approach appears to be one of the most promising concepts of creating efficient, low cost and easily producible organic solar cells. For this purpose one of the best materials was regioregular poly-3-hexylthiophene (P3HT), which is widely used as a donor molecule and a hole transporter, with soluble fullerene derivative (PCBM) as an acceptor and electron transporter. The main drawback of this highly efficient blend is its limited spectral range, covering only a 350–650 nm spectral interval. So the main aim of the present work was to extend the spectral range of the cell up to 850 nm by adding a second bulk heterojunction layer of complementary absorption spe…
Impurity analyses of silicon wafers from different manufacturing routes and their impact on LID of finished solar cells
2013
Summarizes the measurements of impurity concentrations in directionally solidified silicon ingots from different feedstocks. The substitutional Carbon and interstitial Oxygen are measured on as-sawn wafers using FTIR. Active iron concentration is mapped on a-Si:H passivated wafers. It is observed that these impurities present in Elkem Solar Grade Silicon (ESS™) concentrations are comparable to the standard polysilicon which are in the acceptable ranges for silicon for solar industry. The measured LID of the finished solar cells is also comparable.
A bacteriochlorin-diketopyrrolopyrrole triad as a donor for solution-processed bulk heterojunction organic solar cells
2019
We have designed an A–π–D–π–A small-molecule triad consisting of a bacteriochlorin (BC) donor central core linked with two diketopyrrolopyrrole (DPP) acceptors via ethynyl bridges (BC-DPP-1). BC-DPP-1 has a narrow optical bandgap of 1.38 eV with highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels of −4.93 eV and −3.40 eV, respectively, and it was used as an electron donor along with [6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) as an acceptor for solution-processed small-molecule organic solar cells. After optimizing the weight ratio between BC-DPP-1 and PC71BM and pyridine as a solvent additive and subsequent solvent vapor annealing using THF, an …
Review on up/down conversion materials for solar cell application
2012
The present paper reviews the methods of photon up- and down conversion strategies for improving the efficiency of solar cells. Photons with a lower energy than the band gap will be lost in a normal solar cell. The principle of the up conversion technique is that two or more photons are converted into a photon with energy higher than the band gap energy. High energy photons will lose the energy above the band gap energy limit. Down conversion is a process where a high energy photon is converted into several lower energy photons with energies above the band gap. A description is given of the most common methods and materials for these conversions resulting in higher solar cell efficiencies.